{"title":"PCBs","description":"\u003cp\u003eKlipper electronics for Voron and other Klipper printers: toolhead boards, mainboards, stepper drivers, CAN and USB hubs, Nevermore controllers and small helper boards like the MicroFlip. I bring them in from Isik's Tech, BIGTREETECH and TES and ship them from the Netherlands, so you pay no import fees or customs.\u003c\/p\u003e","products":[{"product_id":"isiks-tech-birds-nest-usb-toolchanger-hub","title":"Isik's Tech Birds' Nest USB Hub for Toolchanger 3D Printers","description":"\u003cp\u003eA USB hub for toolchangers that run a USB toolhead board on every tool. One Birds' Nest takes up to six toolheads and gives each one its own protected port, so you run six short cables to a single board instead of six long ones back to the Pi.\u003c\/p\u003e\u003cp\u003eIt runs its own Klipper MCU, so the filament sensors, thermistors and LEDs for each tool connect here too.\u003c\/p\u003e\u003ch3\u003eWhat's on the board\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSTM32G0B1 MCU running Klipper over USB\u003c\/li\u003e\n\u003cli\u003e6× MX3.0 USB toolhead ports with MOSFET and diode protection\u003c\/li\u003e\n\u003cli\u003e6× 3-pin filament sensor ports, 4× thermistor ports, 2× 5V RGB LED ports\u003c\/li\u003e\n\u003cli\u003eUp to 20 A total to the toolheads\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eWith 60 W or bigger hotends at 24 V, heat the tools one after another, not all at once.\u003c\/li\u003e\n\u003cli\u003eThe 5V LED outputs are for a few status LEDs, not LED strips.\u003c\/li\u003e\n\u003cli\u003eMX3.0 and XH connectors are included.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003ePre-order.\u003c\/strong\u003e I'm bringing this board in from Isik's Tech in the US. Expected to ship in 3–4 weeks. As soon as it lands in the Netherlands it goes out to you, and you pay no import fees or customs on top.\u003c\/p\u003e\u003cp\u003eDesigned and assembled by Isik's Tech. Docs: \u003ca href=\"https:\/\/docs.isiks.tech\/birds-nest\/usb\/manual\/\" target=\"_blank\" rel=\"noopener\"\u003ehttps:\/\/docs.isiks.tech\/birds-nest\/usb\/manual\/\u003c\/a\u003e\u003c\/p\u003e","brand":"Isik's Tech","offers":[{"title":"Default Title","offer_id":55040788955463,"sku":"BIRDS-NEST","price":65.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/922B9E61-AE4D-408A-89E9-31DB7FE31618.jpg?v=1789549444"},{"product_id":"isiks-tech-birds-nest-can-toolchanger-hub","title":"Isik's Tech Birds' Nest CAN Hub for Toolchanger 3D Printers","description":"\u003cp\u003eThe CAN version of the Birds' Nest, for toolchangers with a CAN toolhead board on each tool. It doubles as your USB-to-CAN bridge and lays the bus out as a proper linear topology, which is the part most home-made CAN hubs get wrong.\u003c\/p\u003e\u003ch3\u003eWhat's on the board\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSTM32G0B1 MCU running Klipper as USB-to-CAN bridge\u003c\/li\u003e\n\u003cli\u003e6× CAN toolhead ports plus expansion ports for more CAN devices\u003c\/li\u003e\n\u003cli\u003e6× 4-pin filament sensor ports, 6× thermistor ports, 2× 5V ARGB ports\u003c\/li\u003e\n\u003cli\u003eUp to 30 A total to the toolheads\u003c\/li\u003e\n\u003cli\u003e120 Ω termination jumpers, max stub length 300 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eBuilt for 6-wire umbilicals (two twisted CAN pairs plus power), such as Igus CF113-018-D. A 4-wire mode exists but is less reliable.\u003c\/li\u003e\n\u003cli\u003eMX3.0 and XH connectors are included.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003ePre-order.\u003c\/strong\u003e I'm bringing this board in from Isik's Tech in the US. Expected to ship in 3–4 weeks. As soon as it lands in the Netherlands it goes out to you, and you pay no import fees or customs on top.\u003c\/p\u003e\u003cp\u003eDesigned and assembled by Isik's Tech. Docs: \u003ca href=\"https:\/\/docs.isiks.tech\/birds-nest\/can\/manual\/\" target=\"_blank\" rel=\"noopener\"\u003ehttps:\/\/docs.isiks.tech\/birds-nest\/can\/manual\/\u003c\/a\u003e\u003c\/p\u003e","brand":"Isik's Tech","offers":[{"title":"Default Title","offer_id":55040790757703,"sku":"BN-CAN","price":54.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/B78227BE-ECF2-4055-84C3-C3ACC178F90D.jpg?v=1789549507"},{"product_id":"isiks-tech-moar-can-hub","title":"Isik's Tech MOAR_CAN 8\/9 Port CAN Hub, Linear Bus Topology","description":"\u003cp\u003eWhen a printer has more CAN devices than your adapter has ports (a toolchanger, an IDEX, a Box Turtle on the same bus), MOAR_CAN gives you the extra ports without turning the bus into a star. It keeps the linear topology that 1 Mbit CAN wants.\u003c\/p\u003e\u003ch3\u003eSpecs\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e6-pin MX3.0 hub ports, plus a 4-pin MX3.0 aux\/power port (10.5 A max)\u003c\/li\u003e\n\u003cli\u003eXH input from your USB\/CAN adapter, power in through a screw terminal\u003c\/li\u003e\n\u003cli\u003e24 A total, 10.5 A max per device, max stub length 300 mm\u003c\/li\u003e\n\u003cli\u003e120 Ω termination jumper\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWorks with\u003c\/h3\u003e\u003cp\u003eToqueCAN, PiCAN and other USB\/CAN adapters. When you use it with a ToqueCAN, leave the MOAR_CAN termination jumper off. Jumpers, MX3.0 and XH connectors and pins are included.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePre-order.\u003c\/strong\u003e I'm bringing this board in from Isik's Tech in the US. Expected to ship in 3–4 weeks. As soon as it lands in the Netherlands it goes out to you, and you pay no import fees or customs on top.\u003c\/p\u003e\u003cp\u003eDesigned and assembled by Isik's Tech. Docs: \u003ca href=\"https:\/\/docs.isiks.tech\/moar-can\/manual\/\" target=\"_blank\" rel=\"noopener\"\u003ehttps:\/\/docs.isiks.tech\/moar-can\/manual\/\u003c\/a\u003e\u003c\/p\u003e","brand":"Isik's Tech","offers":[{"title":"Default Title","offer_id":55040790790471,"sku":"MOAR-CAN","price":24.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/0C80AACC-02D3-4C9F-AA76-AC1FE80FAB50.jpg?v=1789549508"},{"product_id":"isiks-tech-toquecan-raspberry-pi-can-usb","title":"Isik's Tech ToqueCAN for Raspberry Pi: 2× CAN, 3-Port USB Hub, 24V to 5V 5A","description":"\u003cp\u003eToqueCAN sits on top of a Raspberry Pi 4 or 5 and takes care of the three things every CAN printer build needs around the Pi: a CAN adapter, a USB hub, and a proper 24 V to 5 V supply to power the Pi. That saves you a separate U2C board, a buck converter and a pile of wiring in a small electronics bay.\u003c\/p\u003e\u003ch3\u003eWhat's on the board\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSTM32F072 MCU with 2× Micro-Fit CAN ports and termination jumpers, runs Klipper (bridge mode recommended) or Candlelight\u003c\/li\u003e\n\u003cli\u003e3-port USB hub (USB2514)\u003c\/li\u003e\n\u003cli\u003e24 V to 5 V 5 A regulator powering the Pi and USB devices, 10 A fuse, 8 A max through the CAN ports\u003c\/li\u003e\n\u003cli\u003eMount for a 30 or 40 mm Pi fan with PWM, fan voltage 5 V or 24 V\u003c\/li\u003e\n\u003cli\u003eNeopixel output, GPIO passthrough, MOAR_CAN expansion connector\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eIn the box\u003c\/h3\u003e\u003cp\u003eToqueCAN PCB, M2.5 standoffs, screws and threaded inserts, JST-XH and MX3.0 connectors, jumpers and a 180° USB adapter. Not included: fan, printed fan mount, USB cable. There's no EEPROM, so the Pi won't detect it as an official HAT. That doesn't affect how it works.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePre-order.\u003c\/strong\u003e I'm bringing this board in from Isik's Tech in the US. Expected to ship in 3–4 weeks. As soon as it lands in the Netherlands it goes out to you, and you pay no import fees or customs on top.\u003c\/p\u003e\u003cp\u003eDesigned and assembled by Isik's Tech. Docs: \u003ca href=\"https:\/\/docs.isiks.tech\/toquecan\/manual\/\" target=\"_blank\" rel=\"noopener\"\u003ehttps:\/\/docs.isiks.tech\/toquecan\/manual\/\u003c\/a\u003e\u003c\/p\u003e","brand":"Isik's Tech","offers":[{"title":"Default Title","offer_id":55040790823239,"sku":"TOQUECAN","price":75.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/4430DA61-698A-4086-BFA4-32B3AE2D7953.jpg?v=1789549510"},{"product_id":"isiks-tech-afc-lite-box-turtle-controller","title":"Isik's Tech AFC-Lite Controller PCB for Box Turtle","description":"\u003cp\u003eThe controller board made for Armored Turtle's Box Turtle automated filament changer. One board runs all four lanes: steppers for the extruders, brushed DC drivers for the N20 respooler motors, and all the endstops and LEDs.\u003c\/p\u003e\u003ch3\u003eWhat's on the board\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSTM32H723 MCU, USB-C and CAN (1 Mbit), 24 V in via MX3.0\u003c\/li\u003e\n\u003cli\u003e4× stepstick slots for TMC2209\u003c\/li\u003e\n\u003cli\u003e4× brushed DC motor drivers\u003c\/li\u003e\n\u003cli\u003e12× endstop ports, 4× RGB LED ports, 1× 5 V fan port (always on)\u003c\/li\u003e\n\u003cli\u003eKlipper with Katapult bootloader, works with the AFC Klipper Add-On\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eStepsticks are not included. SPI stepsticks only run in STEP\/DIR mode.\u003c\/li\u003e\n\u003cli\u003eDon't put a Cartographer v3 probe on the same CAN bus (v4 is fine).\u003c\/li\u003e\n\u003cli\u003eMX3.0 and XH connectors are included.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003ePre-order.\u003c\/strong\u003e I'm bringing this board in from Isik's Tech in the US. Expected to ship in 3–4 weeks. As soon as it lands in the Netherlands it goes out to you, and you pay no import fees or customs on top.\u003c\/p\u003e\u003cp\u003eDesigned and assembled by Isik's Tech. Docs: \u003ca href=\"https:\/\/docs.isiks.tech\/box-turtle\/afc-lite\/manual\/\" target=\"_blank\" rel=\"noopener\"\u003ehttps:\/\/docs.isiks.tech\/box-turtle\/afc-lite\/manual\/\u003c\/a\u003e\u003c\/p\u003e","brand":"Isik's Tech","offers":[{"title":"Default Title","offer_id":55040790856007,"sku":"AFC-Lite","price":79.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/EC465E98-5802-4287-A348-ED98AF697D6C.jpg?v=1789549510"},{"product_id":"isiks-tech-owlfc-mini-night-owl-controller","title":"Isik's Tech OwlFC-Mini Controller for Night Owl Filament Changer","description":"\u003cp\u003eIsik's new controller for the Night Owl automatic filament changer. It's small enough to live inside the unit and runs both extruder steppers, all the switches and the LEDs from one board over CAN or USB.\u003c\/p\u003e\u003ch3\u003eWhat's on the board\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSTM32G0B1 MCU, CAN and USB with a MUX\u003c\/li\u003e\n\u003cli\u003e2× TMC2209 stepper drivers for the extruders\u003c\/li\u003e\n\u003cli\u003e7× internal and 2× external switch ports\u003c\/li\u003e\n\u003cli\u003eARGB LED output, optional fan port (always on)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cp\u003eFor a USB connection you also need the Isik's Tech USB Toolhead Adapter, which I sell separately.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePre-order.\u003c\/strong\u003e The OwlFC-Mini is brand new and Isik's first batch ships in late September. Expected to ship from the Netherlands in 3–4 weeks. No import fees or customs on top.\u003c\/p\u003e\u003cp\u003eDesigned and assembled by Isik's Tech.\u003c\/p\u003e","brand":"Isik's Tech","offers":[{"title":"Default Title","offer_id":55040795148615,"sku":"OWLFC-MINI","price":59.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/478D2F0A-880C-4C46-BE76-A311D7891607.jpg?v=1789549569"},{"product_id":"isiks-tech-nevermore-stealthmax-mini-pcb","title":"Isik's Tech Nevermore Stealthmax \u0026 Mini Controller PCB (V1), CAN\/USB","description":"\u003cp\u003eA small Klipper controller for a Nevermore Mini or Stealthmax V1 filter. It gives the filter its own fan control and air-quality readings over CAN or USB, so you don't have to find spare pins on your main board.\u003c\/p\u003e\u003ch3\u003eWhat's on the board\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSTM32G0B1 MCU, Klipper over CAN or vertical Micro-B USB\u003c\/li\u003e\n\u003cli\u003e1× 4-pin PWM fan output\u003c\/li\u003e\n\u003cli\u003e2× I2C sensor ports, 1× LED port, 1× CAN port\u003c\/li\u003e\n\u003cli\u003eSeparate 12–24 V supply, JST-PH connectors and pins included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003ePick your version\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eWith BME280 \u0026amp; SGP40 sensors\u003c\/strong\u003e: comes with the sensors, so you get VOC and temperature readings in Klipper straight away.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNo sensors\u003c\/strong\u003e: board only.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eOnly works with 4-wire PWM fans. 2- and 3-wire fans won't work.\u003c\/li\u003e\n\u003cli\u003eFor Nevermore Mini and Stealthmax V1. Building a Stealthmax V2? Get the Stealthmax PCB 3.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003ePre-order.\u003c\/strong\u003e I'm bringing this board in from Isik's Tech in the US. Expected to ship in 3–4 weeks. As soon as it lands in the Netherlands it goes out to you, and you pay no import fees or customs on top.\u003c\/p\u003e\u003cp\u003eDesigned and assembled by Isik's Tech. Docs: \u003ca href=\"https:\/\/docs.isiks.tech\/nevermore\/controller\/\" target=\"_blank\" rel=\"noopener\"\u003ehttps:\/\/docs.isiks.tech\/nevermore\/controller\/\u003c\/a\u003e\u003c\/p\u003e","brand":"Isik's Tech","offers":[{"title":"With BME280 \u0026 SGP40 sensors","offer_id":55040795181383,"sku":"NM-SM-SENS","price":59.95,"currency_code":"EUR","in_stock":true},{"title":"No sensors","offer_id":55040795214151,"sku":"NM-SM","price":28.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/FullSizeRender.jpg?v=1789549570"},{"product_id":"isiks-tech-nevermore-stealthmax-pcb-3","title":"Isik's Tech Nevermore Stealthmax PCB 3 for Stealthmax V2, CAN\/USB-C","description":"\u003cp\u003eThe controller for a Nevermore Stealthmax V2. Everything the V2 can do runs from this one board in Klipper: the fan, the servo that closes the vent, a Peltier or heater, UV LEDs and the air-quality sensors.\u003c\/p\u003e\u003ch3\u003eWhat's on the board\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSTM32G0B1 MCU, Klipper over CAN or USB-C\u003c\/li\u003e\n\u003cli\u003e24 V (VIN) 4-pin PWM fan output\u003c\/li\u003e\n\u003cli\u003e2× I2C sensor ports for SGP40\/BME280\u003c\/li\u003e\n\u003cli\u003e3× thermistor ports plus an onboard thermistor\u003c\/li\u003e\n\u003cli\u003ePeltier MOSFET, constant-current UV LED driver, ARGB and servo outputs\u003c\/li\u003e\n\u003cli\u003eSlide switch for CAN termination, MX3.0 for power and CAN, 5 V buck converter\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eThe sensor boards are sold separately, and you need two. See Nevermore Sensors.\u003c\/li\u003e\n\u003cli\u003eA CAN port cover (XT30 or MX3.0) is optional and makes the wiring plug-and-play.\u003c\/li\u003e\n\u003cli\u003eAll PH and MX3.0 connectors you need are included.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003ePre-order.\u003c\/strong\u003e Isik has this board on backorder until October, so expect it to ship from the Netherlands in 4–6 weeks. No import fees or customs on top.\u003c\/p\u003e\u003cp\u003eDesigned and assembled by Isik's Tech. Docs: \u003ca href=\"https:\/\/docs.isiks.tech\/Nevermore\/Controller\/\" target=\"_blank\" rel=\"noopener\"\u003ehttps:\/\/docs.isiks.tech\/Nevermore\/Controller\/\u003c\/a\u003e\u003c\/p\u003e","brand":"Isik's Tech","offers":[{"title":"Default Title","offer_id":55040795246919,"sku":"NM-SM3","price":69.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/3EB18A0B-BC56-45E0-9F9E-C05EB7414C47.jpg?v=1789549571"},{"product_id":"isiks-tech-nevermore-bme280-sgp40-sensor","title":"Isik's Tech BME280 \u0026 SGP40 Air Quality Sensor for Nevermore Filters","description":"\u003cp\u003eA tiny sensor board (10.6 × 10.6 mm) with a BME280 for temperature, humidity and pressure and an SGP40 for VOCs. Put one on the intake and one on the exhaust of your Nevermore and Klipper shows you how well the filter is working.\u003c\/p\u003e\u003ch3\u003eSpecs\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eBME280 + SGP40 on one board\u003c\/li\u003e\n\u003cli\u003e3.3 V, I2C\u003c\/li\u003e\n\u003cli\u003ePlugs into the sensor ports on the Stealthmax PCB 3 and the Stealthmax \u0026amp; Mini PCB\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cp\u003eThe Stealthmax PCB 3 uses two, one for intake and one for exhaust. The price is per sensor board.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePre-order.\u003c\/strong\u003e I'm bringing this board in from Isik's Tech in the US. Expected to ship in 3–4 weeks. As soon as it lands in the Netherlands it goes out to you, and you pay no import fees or customs on top.\u003c\/p\u003e\u003cp\u003eDesigned and assembled by Isik's Tech.\u003c\/p\u003e","brand":"Isik's Tech","offers":[{"title":"Default Title","offer_id":55040795279687,"sku":"NM-SENS","price":29.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/Naamloos_-_2025-05-01T171004.225.jpg?v=1789549571"},{"product_id":"isiks-tech-stealthmax-pcb-3-can-port-cover","title":"Isik's Tech Stealthmax PCB 3 CAN Port Cover, XT30 or MX3.0 Daisy Chain","description":"\u003cp\u003eA port cover for a Stealthmax V2 build with the PCB 3. It comes with the internal cable already crimped and soldered, so you plug it into the PCB 3 and close the lid. No crimping inside a cramped filter housing.\u003c\/p\u003e\u003ch3\u003ePick your connector\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eXT30 (2+2)\u003c\/strong\u003e: XT30 connector for power and CAN.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMX3.0 with daisy chain\u003c\/strong\u003e: Micro-Fit 3.0 connector with a daisy-chain port to carry the CAN bus on to the next device.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFits\u003c\/h3\u003e\u003cp\u003eNevermore Stealthmax V2 with the Isik's Tech Stealthmax PCB 3.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePre-order.\u003c\/strong\u003e I'm bringing these in from Isik's Tech in the US. Expected to ship in 3–4 weeks. As soon as they land in the Netherlands yours goes out to you, and you pay no import fees or customs on top.\u003c\/p\u003e\u003cp\u003eDesigned and assembled by Isik's Tech.\u003c\/p\u003e","brand":"Isik's Tech","offers":[{"title":"XT30 (2+2)","offer_id":55040797704519,"sku":"NM-SM3-XT30-PC","price":8.95,"currency_code":"EUR","in_stock":true},{"title":"MX3.0 with daisy chain","offer_id":55040797737287,"sku":"NM-SM3-MX3.0-PC","price":9.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/Stealthmax3MX3.0PCPhoto.jpg?v=1789549624"},{"product_id":"isiks-tech-jst-xh-fan-splitter","title":"Isik's Tech 2-Pin JST-XH Fan Splitter, 1 to 3","description":"\u003cp\u003eA tiny PCB that turns one 2-pin JST-XH fan output into three. Handy when your board has fewer fan ports than your electronics bay has fans.\u003c\/p\u003e\u003ch3\u003eSpecs\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e4× 2-pin JST-XH connectors: 1 in, 3 out\u003c\/li\u003e\n\u003cli\u003e4 male connector housings with pins included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cp\u003eIt splits power only, so there's no tach or PWM signal. Every fan on the splitter runs at the same speed.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePre-order.\u003c\/strong\u003e I'm bringing this board in from Isik's Tech in the US. Expected to ship in 3–4 weeks. As soon as it lands in the Netherlands it goes out to you, and you pay no import fees or customs on top.\u003c\/p\u003e\u003cp\u003eDesigned and assembled by Isik's Tech.\u003c\/p\u003e","brand":"Isik's Tech","offers":[{"title":"Default Title","offer_id":55040797802823,"sku":"XH-SPLIT","price":5.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/il_1140xN.5154992446_27jk.jpg?v=1789549625"},{"product_id":"isiks-tech-usb-toolhead-adapter","title":"Isik's Tech USB Adapter for Toolhead Boards","description":"\u003cp\u003eLets you run a USB toolhead board (or a board like the OwlFC-Mini) over a single umbilical to your Raspberry Pi, instead of setting up CAN. It uses the same protection circuit as the Birds' Nest USB hub.\u003c\/p\u003e\u003ch3\u003eWorks with\u003c\/h3\u003e\u003cp\u003eUSB toolhead boards and the OwlFC-Mini in USB mode.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePre-order.\u003c\/strong\u003e I'm bringing this board in from Isik's Tech in the US. Expected to ship in 3–4 weeks. As soon as it lands in the Netherlands it goes out to you, and you pay no import fees or customs on top.\u003c\/p\u003e\u003cp\u003eDesigned and assembled by Isik's Tech.\u003c\/p\u003e","brand":"Isik's Tech","offers":[{"title":"Default Title","offer_id":55040797901127,"sku":"USB-ADAPTER","price":9.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/1C5D28EC-AE0A-4B67-B03A-C7A696FCB3A2.jpg?v=1789549626"},{"product_id":"isiks-tech-hedgehog-klipper-io-expander","title":"Isik's Tech Hedgehog CAN\/USB Klipper I\/O Expander, 31 Pins","description":"\u003cp\u003eOut of pins on your main board? Hedgehog adds 31 I\/O pins to Klipper over CAN or USB. Each pin sits on a standard 2.54 mm header with its own 3.3 V and GND pair next to it, so a switch, sensor or relay plugs in without a breadboard.\u003c\/p\u003e\u003ch3\u003eWhat's on the board\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSTM32G0B1 MCU, built-in CAN transceiver plus USB\u003c\/li\u003e\n\u003cli\u003e31 I\/O pins on 2.54 mm headers, 3.3 V\/GND beside each\u003c\/li\u003e\n\u003cli\u003ePull-ups and protection for 3 thermistors\u003c\/li\u003e\n\u003cli\u003e24 V input with onboard 3.3 V and 5 V regulators, 120 Ω CAN termination jumper\u003c\/li\u003e\n\u003cli\u003eKlipper with Katapult support; also runs STM32Duino\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003ePick your version\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSoldered\u003c\/strong\u003e: pin headers already soldered on.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNot soldered\u003c\/strong\u003e: bare board, solder only the headers you need.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eGood to know\u003c\/h3\u003e\u003cp\u003eThe pins have no preset functions. You configure every one yourself in Klipper, and some SPI pins aren't supported by Klipper.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003ePre-order.\u003c\/strong\u003e I'm bringing this board in from Isik's Tech in the US. Expected to ship in 3–4 weeks. As soon as it lands in the Netherlands it goes out to you, and you pay no import fees or customs on top.\u003c\/p\u003e\u003cp\u003eDesigned and assembled by Isik's Tech. Docs: \u003ca href=\"https:\/\/docs.isiks.tech\/hedgehog\/manual\/\" target=\"_blank\" rel=\"noopener\"\u003ehttps:\/\/docs.isiks.tech\/hedgehog\/manual\/\u003c\/a\u003e\u003c\/p\u003e","brand":"Isik's Tech","offers":[{"title":"Soldered","offer_id":55040797933895,"sku":"HEDGEHOG-SOLDERED","price":30.95,"currency_code":"EUR","in_stock":true},{"title":"Not soldered","offer_id":55040797966663,"sku":"HEDGEHOG-NOPINS","price":25.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/59F14A12-C12B-4814-A7FF-41951CCED74D.jpg?v=1789549626"},{"product_id":"bigtreetech-ebb36-can-v1-2-toolhead-board-stm32g0b1-max31865","title":"BIGTREETECH EBB36 CAN V1.2 Toolhead Board — STM32G0B1, MAX31865","description":"\u003cp\u003eA proven CAN toolhead board for Klipper printers. The EBB36 bolts to the back of a 36 mm pancake extruder motor and runs the extruder, hotend heater, thermistor, fans, probe and LEDs from one board, so the umbilical to your toolhead shrinks to power plus two data wires. It talks to Klipper over CAN or USB.\u003c\/p\u003e\n\u003cp\u003eThis is the V1.2 with the STM32G0B1 chip and the MAX31865 on board, so it reads PT100 and PT1000 sensors directly as well as regular 100K NTC thermistors. An ADXL345 accelerometer is built in for input shaping, so no separate sensor on the toolhead.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eMCU: ARM Cortex-M0+ STM32G0B1CBT6, 64 MHz\u003c\/li\u003e\n\u003cli\u003eInput: 12–24 V DC, 6 A\u003c\/li\u003e\n\u003cli\u003eStepper driver: TMC2209 on board\u003c\/li\u003e\n\u003cli\u003eHeater output (E0): 5 A max\u003c\/li\u003e\n\u003cli\u003eFans: 2 × PWM outputs (FAN0, FAN1), 1 A, 1.5 A peak\u003c\/li\u003e\n\u003cli\u003eTemperature: 1 × 100K NTC or PT1000 (TH0), 1 × PT100\/PT1000 via MAX31865, 2- or 4-wire\u003c\/li\u003e\n\u003cli\u003eAccelerometer: ADXL345\u003c\/li\u003e\n\u003cli\u003eCommunication: CAN or USB, 120 Ω CAN termination selectable by jumper\u003c\/li\u003e\n\u003cli\u003eSize: 51.5 × 37 mm, 2 × M3 mounting holes at 43.85 mm spacing\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eFor CAN you need either a USB-to-CAN adapter or a mainboard that can act as a CAN bridge, such as the Manta M8P. Boot and reset buttons let you flash Klipper over USB in DFU mode. Protection is built in on the thermistor input, heater and fan outputs (flyback diodes) and power input (reverse polarity). Wiring diagrams and sample Klipper configs are on \u003ca href=\"https:\/\/github.com\/bigtreetech\/EBB\" rel=\"noopener\"\u003eBIGTREETECH's EBB GitHub\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePre-order.\u003c\/strong\u003e I'm bringing this board in directly from BIGTREETECH. Expected to ship in 3–4 weeks. As soon as it lands in the Netherlands it goes out to you, and you pay no import fees or customs on top.\u003c\/p\u003e\n\u003cp\u003eBIGTREETECH part number 1030000175.\u003c\/p\u003e","brand":"BIGTREETECH","offers":[{"title":"Default Title","offer_id":55056298180935,"sku":"1030000175","price":33.99,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/EBB-36_7899172f-17a5-4310-8807-74e88e0aac27.jpg?v=1789641974"},{"product_id":"bigtreetech-ebb36-gen2-v1-0-toolhead-board-can-usb-tacho-fan-lis2dw","title":"BIGTREETECH EBB36 Gen2 V1.0 Toolhead Board — CAN\/USB, Tacho Fan, LIS2DW","description":"\u003cp\u003eBIGTREETECH's second-generation EBB36, rebuilt around the things that kill toolhead boards: nearly every input and output is protected against wiring mistakes, and it's tested in chambers up to 75 °C. It mounts on a 36 mm pancake extruder motor and runs the extruder, heater, thermistor, fans, probe and LEDs over a single CAN or USB connection to Klipper.\u003c\/p\u003e\n\u003cp\u003eSwitching between CAN and USB is one jumper, and the passthrough port follows along. The hotend fan header reads tacho, so Klipper can stop a print if that fan dies. Every fan output lets you pick 5 V or 24 V, and a dedicated thermistor watches the stepper driver's temperature.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eMCU: ARM Cortex-M0+ STM32G0B1CBT6, 64 MHz\u003c\/li\u003e\n\u003cli\u003eInput: 24–28 V DC (not for 12 V printers)\u003c\/li\u003e\n\u003cli\u003eStepper driver: TMC2209 on board\u003c\/li\u003e\n\u003cli\u003eHeater output: 120 W (24 V \/ 5 A)\u003c\/li\u003e\n\u003cli\u003eFans: 2 × 2-pin PWM (FAN0, FAN1), 1 × 3-pin with tacho (FAN2), 5 V\/24 V selectable; 1 A total, 1.5 A peak\u003c\/li\u003e\n\u003cli\u003e5 V output: 1.5 A peak\u003c\/li\u003e\n\u003cli\u003eThermistor: PT1000 or NTC\u003c\/li\u003e\n\u003cli\u003eAccelerometer: LIS2DW on board\u003c\/li\u003e\n\u003cli\u003eI²C port for sensors such as Eddy probes or chamber\/environment sensors\u003c\/li\u003e\n\u003cli\u003eConnectors: XT30 power, JST-XH motor and CAN, Molex heater terminals\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eFor CAN you need a USB-to-CAN adapter or a mainboard that acts as a CAN bridge, such as the Manta M8P. Upgrading from an EBB36 V1.2? The Gen2 needs 24 V and has its own pinout and Klipper config, so check your wiring before you swap. Pinouts and sample configs are on \u003ca href=\"https:\/\/github.com\/bigtreetech\/EBB\/tree\/master\/EBB_GEN2\/EBB36_GEN2\" rel=\"noopener\"\u003eBIGTREETECH's GitHub\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePre-order.\u003c\/strong\u003e I'm bringing this board in directly from BIGTREETECH. Expected to ship in 3–4 weeks. As soon as it lands in the Netherlands it goes out to you, and you pay no import fees or customs on top.\u003c\/p\u003e\n\u003cp\u003eBIGTREETECH part number 1030000188.\u003c\/p\u003e","brand":"BIGTREETECH","offers":[{"title":"Default Title","offer_id":55056298770759,"sku":"1030000188","price":44.99,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/5_0703fee9-dbbd-4a54-b2b9-0c6984004426.jpg?v=1789641990"},{"product_id":"bigtreetech-tmc2209-v1-3-stepper-motor-driver-uart-sensorless-homing","title":"BIGTREETECH TMC2209 Stepper Motor Driver — UART, Sensorless Homing","description":"\u003cp\u003eThe quiet, dependable stepstick driver most Klipper boards are built around. Plug it into any board with standard stepstick sockets, such as the Manta M8P, Octopus or SKR, and run it in UART mode so Klipper sets current and microstepping from your config, no potentiometer tweaking.\u003c\/p\u003e\n\u003cp\u003eStealthChop2 keeps motors near silent at lower speeds, SpreadCycle takes over when you need torque, and StallGuard4 lets you home X and Y without endstop switches.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eChip: Trinamic TMC2209\u003c\/li\u003e\n\u003cli\u003eMotor voltage (VM): 4.75–28 V DC\u003c\/li\u003e\n\u003cli\u003eCurrent: 2.0 A RMS, 2.8 A peak\u003c\/li\u003e\n\u003cli\u003eMicrostepping: up to 1\/256 (MicroPlyer interpolation)\u003c\/li\u003e\n\u003cli\u003eModes: UART or STEP\/DIR\u003c\/li\u003e\n\u003cli\u003eFeatures: StealthChop2, SpreadCycle, StallGuard4, CoolStep\u003c\/li\u003e\n\u003cli\u003eSense resistor: 110 mΩ\u003c\/li\u003e\n\u003cli\u003eSize: 15.24 × 20.32 mm stepstick format\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eSold per piece; order one for each motor. For 48 V or high-current motors, look at the TMC5160T Plus instead.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePre-order.\u003c\/strong\u003e I'm bringing these in directly from BIGTREETECH. Expected to ship in 3–4 weeks. As soon as they land in the Netherlands they go out to you, and you pay no import fees or customs on top.\u003c\/p\u003e\n\u003cp\u003eBIGTREETECH part number 1040000053.\u003c\/p\u003e","brand":"BIGTREETECH","offers":[{"title":"Default Title","offer_id":55056299426119,"sku":"1040000053","price":7.89,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/1_559a8099-e380-4d84-8920-7649c1ddf37b.jpg?v=1789642006"},{"product_id":"bigtreetech-tmc5160t-plus-stepper-driver-60-v-spi-without-heatsink-case","title":"BIGTREETECH TMC5160T Plus Stepper Driver — 60 V SPI, without Heatsink Case","description":"\u003cp\u003eA high-voltage stepper driver for when TMC2209s run out of headroom. Run your A\/B motors at 48 V and they hold torque at speeds where a 24 V setup starts skipping. It fits the high-voltage driver sockets on boards like the Manta M8P V2.0 and Octopus Pro, and Klipper controls it over SPI.\u003c\/p\u003e\n\u003cp\u003eThis is the Plus without the enclosed heatsink case: the same TMC5160-TA chip and eight separate high-power MOSFETs, in a smaller 58 × 50 × 28 mm package that fits tighter electronics bays.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eChip: Trinamic TMC5160-TA\u003c\/li\u003e\n\u003cli\u003eInput voltage (HVIN): 8–56 V (60 V max)\u003c\/li\u003e\n\u003cli\u003eCurrent: up to 10.6 A RMS, 15 A sine-wave peak\u003c\/li\u003e\n\u003cli\u003eMOSFETs: 8 × external, 100 V \/ 93 A, down to 6 mΩ\u003c\/li\u003e\n\u003cli\u003eSense resistor: 22 mΩ\u003c\/li\u003e\n\u003cli\u003eCapacitors: 2 × 560 µF\u003c\/li\u003e\n\u003cli\u003eModes: SPI or STEP\/DIR; StealthChop and SpreadCycle\u003c\/li\u003e\n\u003cli\u003e24 V always-on fan header for active cooling\u003c\/li\u003e\n\u003cli\u003eSize: 58 × 50 × 28 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eSold per piece. Check that your board's driver socket supports high voltage and SPI, and set its motor power jumper correctly before powering up: 48 V into a 24 V-only socket will destroy the board. Point a fan at it for sustained high current. Documentation is on \u003ca href=\"https:\/\/github.com\/bigtreetech\/BIGTREETECH-Stepper-Motor-Driver\" rel=\"noopener\"\u003eBIGTREETECH's GitHub\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePre-order.\u003c\/strong\u003e I'm bringing these in directly from BIGTREETECH. Expected to ship in 3–4 weeks. As soon as they land in the Netherlands they go out to you, and you pay no import fees or customs on top.\u003c\/p\u003e\n\u003cp\u003eBIGTREETECH part number 1050000072.\u003c\/p\u003e","brand":"BIGTREETECH","offers":[{"title":"Default Title","offer_id":55056300376391,"sku":"1050000072","price":23.99,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/TMC5160TPlus_Wocase_3.jpg?v=1789642019"},{"product_id":"bigtreetech-manta-m8p-v2-0-klipper-mainboard-stm32h723-8-motors-cb1-cm4","title":"BIGTREETECH Manta M8P V2.0 Klipper Mainboard — STM32H723, 8 Motors, CB1\/CM4","description":"\u003cp\u003eA Klipper mainboard with the Linux computer built in. The Manta M8P V2.0 has a socket for a BIGTREETECH CB1 or Raspberry Pi CM4 core board, so there's no separate Pi to mount, power and cable up. Eight motor outputs cover a Voron 2.4's four Z motors, A\/B and extruder with one to spare, and the fast STM32H723 handles it all without breaking a sweat.\u003c\/p\u003e\n\u003cp\u003eEach driver socket can run at 24 V or at high voltage up to 60 V, so you can put TMC5160s on A\/B at 48 V and keep TMC2209s elsewhere. A CAN port lets the board bridge straight to an EBB36 toolhead board.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eMCU: ARM Cortex-M7 STM32H723ZET6, 550 MHz\u003c\/li\u003e\n\u003cli\u003eBoard input: 12 V or 24 V DC; driver voltage 24 V or HV (24–60 V) selectable per socket\u003c\/li\u003e\n\u003cli\u003eMotors: 8 driver sockets (Motor 1–3 with dual outputs), SPI, UART or STEP\/DIR\u003c\/li\u003e\n\u003cli\u003eHeaters: heated bed 10 A (10.5 A peak), 4 × hotend heater 5.5 A (6 A peak)\u003c\/li\u003e\n\u003cli\u003eFans: 5 × 2-pin PWM, 2 × 4-pin PWM, 1 × Pi fan, 1 × always-on; 5\/12\/24 V selectable, 1 A each\u003c\/li\u003e\n\u003cli\u003eTemperature: 5 × 100K NTC inputs, 4 of which also take PT1000\u003c\/li\u003e\n\u003cli\u003eExpansion: CAN, BLTouch, servo, filament sensor, power-loss detection, PS-ON, I²C, RGB, SPI (for accelerometers), TFT, EXP\u003c\/li\u003e\n\u003cli\u003eCore board functions: 3 × USB 2.0, LAN, HDMI, DSI, CSI, 40-pin GPIO\u003c\/li\u003e\n\u003cli\u003eSize: 170 × 102.7 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eBoard only: no core board (CB1\/CM4) and no stepper drivers are included. HDMI, TFT35 SPI and USB camera work with the CB1; the CSI\/DSI ports only work with a CM4. Total current for heaters, drivers and fans must stay under 12 A. Manual, pinout and sample configs are on the \u003ca href=\"https:\/\/global.bttwiki.com\/M8P-V2_0.html\" rel=\"noopener\"\u003eBIGTREETECH wiki\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePre-order.\u003c\/strong\u003e I'm bringing this board in directly from BIGTREETECH. Expected to ship in 3–4 weeks. As soon as it lands in the Netherlands it goes out to you, and you pay no import fees or customs on top.\u003c\/p\u003e\n\u003cp\u003eBIGTREETECH part number 1020000442.\u003c\/p\u003e","brand":"BIGTREETECH","offers":[{"title":"Default Title","offer_id":55056301228359,"sku":"1020000442","price":84.38,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/MantaM8PV2_6.jpg?v=1789642034"},{"product_id":"tes-microflip-n20-motor-reverser-pcb-for-goose-belt-purger","title":"TES MicroFlip N20 Motor Reverser PCB for Goose Belt Purger","description":"\u003cp\u003eA thumb-sized board that goes between your controller and the N20 motor on a Goose Belt Purger. The protection parts the GBP docs ask for are already on the board, so you don't have to solder a diode, resistor and capacitor onto the motor leads. Belt running the wrong way? Flip the slide switch instead of re-crimping the wires.\u003c\/p\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eFor N20-size brushed DC gear motors, 3–12 V, up to 1 A\u003c\/li\u003e\n\u003cli\u003eDPDT slide switch that swaps both motor leads\u003c\/li\u003e\n\u003cli\u003eRC snubber on board against brush noise and voltage spikes\u003c\/li\u003e\n\u003cli\u003e2-pin JST-PH connector\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIn the bag\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eMicroFlip PCB\u003c\/li\u003e\n\u003cli\u003e1× 2-pin JST-PH housing with 4 crimp pins (you need 2, the other 2 are spares)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eGood to know\u003c\/h3\u003e\n\u003cp\u003eThe board is rated for 12 V. If your fan outputs run at 24 V, take the motor power from a 12 V or 5 V output instead.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIn stock in the Netherlands.\u003c\/strong\u003e It ships from my workshop within 2–4 working days, no import fees or customs on top.\u003c\/p\u003e\n\u003cp\u003eDesigned by Tröndle Embedded Systems (TES) in Switzerland, open source under GPL-3.0.\u003c\/p\u003e","brand":"Tröndle Embedded Systems","offers":[{"title":"Default Title","offer_id":55059882967367,"sku":"TES-MICROFLIP","price":3.99,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/files\/image.jpg?v=1789660151"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0878\/0575\/5719\/collections\/4430DA61-698A-4086-BFA4-32B3AE2D7953.jpg?v=1789661530","url":"https:\/\/pjotr3dshop.com\/collections\/pcbs.oembed","provider":"Pjotr3DShop","version":"1.0","type":"link"}